Netum RS-8000 Wearable Bluetooth Ring Scanner User Manual

Netum RS-8000 Wearable Bluetooth Ring Scanner User Manual

Package Included:

• 1 x Scanner; 1 x Dock;
• 1 x USB cable; 2 x Batteries;
• 1 x Quick Manual;

Product Information

1. Scanning Window
2. Scanner LED
3. Battery Door
4. Buzzer
5. Trigger Button
6. Adjustable Ring Belt

1. Battery Charging Dock
2. DC Port
3. Type C Port
4. Bluetooth LED
5. Transmission LED
6. Battery charging LED
7. Scanner Power charging LED

Charge The Battery

• Press and push up the battery door
• Insert battery and secure battery door

Scanner’s Bluetooth Connection Status

1. Solid Blue- Bluetooth Connected
2. Flashing Blue- Bluetooth Disconnected/Bluetooth Pairing

Battery Dock LED Status：

1. Scanner LED
   Solid Red- Full Charged
   Flashing Red- Charging
2. Battery LED
   Solid Red- Full Charged
   Flashing Red – Charging
3. Transmission LED
   Solid Green- No Transmit
   Flashing Green- Transferring data
4. Bluetooth connection status
   Solid Blue- Scanner has connected with the dock
   Flashing Blue- Scanner has disconnected with the dock

Setup Guide

Get Started

• Pair Netum bluetooth (refer to the section of “Bluetooth pairing”)
• Setup keyboard language: US keyboard is set by default. If you use other type of keyboard please refer to the section of “keyboard language”.
• Locate cursor on place where you want the data to be displayed after that you can start to scan.
• Firmware Version
  Read below command barcode to check scanner firmware version.

Barcode Programming

Netum barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.

Bluetooth Pairing

How to pair scanner’s bluetooth with the dock ?

• Connect the dock with your computer via USB cable.
• Scan QR code from the dock, Bluetooth paired once blue LED on the dock turns to solid blue.
• If you want to disconnect it with the dock and connect it with your device, scan “Bluetooth HID” then pair Netum Bluetooth.

Important Note: Default Idle Time: Scanner will power off automatically if device is not connected in 3mins . If you want BLE and SPP mode, please contact us.

• Keyboard Language
  For example If you use French Keyboard, scan command barcode of “French keyboard ”. If you use a US keyboard you can ignore this step

Data Uploading Mode

If you are heading for a working area which lies outside the bluetooth signal range, you may activate scanner’s store mode, following steps described below. Under this mode,all scanned data will be stored directly into the buffer memory of the device. Furthermore, the data entries will be permanently saved in the buffer memory prior to the manual upload into the working station, so that you may upload them when you are near your working device. By scanning the following barcode, the device leaves the offline mode, normal mode will be reinitialised.

• Offline Mode
  By scanning the following barcode, the offline mode will be activated.

Get Battery Volume

Scan below command barcode to get battery rough volume.

• Voltage < 3.5V, Low battery Volume, there will have 5 beeps after each
  scan. Scanner can not be able to read any barcodes.
• 3.7V< Voltage < 3.5V, Low battery Volume, there will have 2 beeps after
  each scan. Scanner still be able to read barcodes.
• Voltage >4.2V , Full Volume
• Idle time
  Scanner will turn to sleep after idle/inactive for 1min Scan “Disable module Idle time” before you doing any other setup from this section.

IOS Keyboard POP UP/HIDE

During the scanning IOS keyboard can be hided or popped up by scanning below command barcode.

• Scan this barcode at Bluetooth HID connected state on IOS device, popup IOS keyboard.

Note: Two short beeps after scan indicates disable, one long sound with three tones indicates enable.

• Beeper
  Enable/Disable scanner to beep to indicate successful scan.

• Factory Restore
  Scan below command barcode will reset the scanner.

Beep Tone Indication

Веер Туре

Beep/Tone
Indication
1 Beep in 2 Tones
Scan Code under Store Mode/ Power Off
Prompt Tone
1 Beep in 3 Tones
Power On/ Successful Configuration/ Finish Uploading
1 Short Beep
Successful Scan
Two Beeps in Same Tone Low Battery Volume Warning
Warning Tone Three Beeps in Same Tone Error on saving barcodes under Store Mode
Transmission failed
Five Beeps in Same Tone Fail to power on due to low battery volume

REFRENCE LINK