PYLE Wireless BT Hybrid Amplifier Receiver featured

PYLE Wireless BT Hybrid Amplifier Receiver manual

pyle logo

PYLE Wireless BT Hybrid Amplifier Receiver manual

PYLE Wireless BT Hybrid Amplifier Receiver

Safety Instructions

  • Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be strong enough to create a risk electric shock to a person.
  • Intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

CAUTION: To reduce the risk of electric shock, DO NOT ATTEMPT TO OPEN THE AMPLIFIER OR REMOVE THE COVER. There are no user serviceable parts inside – please use a qualified technician for all servicing.

WARNING: To prevent electrical shock or fire hazard ,this amplifier should not be exposed to rain or moisture. Do not place objects filled with liquid, such as vases, on the amplifier.


  1. Power Source
    The unit should be connected to a power supply AC-115V/60Hz, AC-230V/50Hz.
  2. Ventilation
    The unit should be situated so that its location or position does not interfere with its proper ventilation. Place the unit at least 10cm away from the walls.
  3. Water and Moisture
    The unit should not be used near water-for example, near a swimming pool in a wet basement, etc.
  4. Electric Shock
    If a metal object, such as hair pin or needle comes into contact inside this unit, a dangerous electric shock may result. For families with children, never permit children to put anything, especially metal, inside this unit.
  5. Enclosure Removal
    Never remove the enclosure. If the internal parts are touched accidentally, a serious electric shock might occur.
  6. Abnormal Smell
    If an abnormal smell or smoke is detected, immediately turn the power OFF and pull out the power cord. Contact your dealer or nearest service station.


PYLE Wireless BT Hybrid Amplifier Receiver fig 1

  1. POWER SWITCH: Press to switch the power unit ON or OFF.
  2. ⇐: This knob is used to select the preview station which has been kept in system.
  3. RPT button: Repeat music control
  4. ⇒: This knob is used to select the next station which has been kept in system.
  5. EQ button control for Hall, Live, Jazz, Rock, Pop, Normal.
  6. : play/pause song button on USB/SD card
  8. Mode switch button for input choice like USB/SD/BT/FM
  9. Source Input OPTI/COAX
  13. MASTER VOLUME CONTROL: Adjusts the blue lights and blue rings. Adjusts the volume level. Turn the knob clockwise to increase the volume.
  14. ECHO CONTROL: Turn the knob to adjust the MIC echo level.
  15. TREBLE: Adjusts the master treble
  16. BASS: Adjusts the master bass
  17. MIC VOLUME: Adjusts the volume level. Turn the knob clockwise to increase the MIC volume .
  18. USB/SD: Card input
  19. MIC INPUT JACKS 1 & 2 KARAOKE MIC: Connect to these jacks.
  20. HEADPHONE JACK: Headphone connect to this jack.
  21. INPUT SELECTOR: Turn this button to choose the favorable input
  25. AUX 1 Input


PYLE Wireless BT Hybrid Amplifier Receiver fig 2

  1. TUNER ANT: Connect for AM and FM antennas.
    Connect the audio output jacks of CDNCD/DVD, AUX to these jacks.
  3. SUB-WOOFER OUTPUT JACKS 1 & 2: Connect IPOD/MP3 to this jack.
  4. LINE OUTPUT JACKS: Connect the line input jacks to these jacks.
  5. A SPEAKER OUTPUT TERMINALS: Connect your speaker system to these terminals.
    Connect your the other speaker system(s) to these terminals.
  8. 115V/230V SWITCH: According to power voltage, push this button to the station of the 115V or 230V.
  9. POWER CORD: Connect to AC 115V/60Hz & 230V/50Hz outlet.


PYLE Wireless BT Hybrid Amplifier Receiver fig 3

  • A. Press MODE button under the LCD display screen and enter into Wireless BT mode.
  • B. Search on the Wireless BT device and you can fnd the Wireless BT name “PYLE PRO”
  • C. Select the “PYLE PRO” Wireless BT name and wait for the device to pair.
  • D. The unit will make a signal to confrm that the device has successfully paired and the screen will display “BLUETOOTH CONNECTED”
  • E. Once being paired, you can play music from your BT device. You can also use the control buttons on the unit to select the tracks from your BT device.

Remote Control

PYLE Wireless BT Hybrid Amplifier Receiver fig 4

  1. Standby Button
  2. Equalizer Button
    (HaII, Liv e, Jazz, Rock, Pop, NormaI)
  3. Previous Song Button
    • Short press for previous music in
      BT/USB/SD system, or for previous program in AM/FM system.
    • Press and hold this button to auto scan the programs downward in AM/FM syst em, and automatic memory to the prog ram number .
  4.  Source Input Volume
  5. MODE
    Menu Control Button. Press to select BT/USB/SD/AM/FM/LINE IN etc. audio input
  6. MUTE Button
    This function only works in radio/BT/USB/SD/AM/FM state
  7. Source Input Volume +
    This function only works in BT/USB/SD state
  8. SCAN Button
    Press this button to auto scan the programs in AM/FM system, and automatic memory to program number.

How to replace the preset radio stations?

  • Use the remote control to set the radio stations.
  • Use button of the front panel set the radio stations.

NOTE: The preset stations can’t be deleted, BUT CAN BE REPLACED.

Operations Steps
  1. Rotate the input selector switch to the BT/MP3/AM/FM/OPTI/COAX position.
  2. Press the Mode key of the front panel or remote to select AM/FM.
  3. / : Press the button to adjust to your favorite station number, then, press and hold this button to auto scan the programs downward or upward, It will not stop until the tuner is found, and the tuner will automatic replace your favorite station number.

In this way, you can replace the preset radio stations.


  1. Make sure that all connections are properly connected and the main volume is set to minimum level before turning ON the unit.
  2. When more than one pair of speakers are used, (specially the main speaker output) make sure that the speakers used are of the same wattage and impedance, otherwise the unit maybe damaged under high power or long term operation.
  3. To avoid humming sounds and unwanted noise, make sure that all the wires are properly inserted
  4. For speaker cords, strip off the vinyl coating and twist the wire tip.
    Push down the pink jack or loosen the screw terminal, before inserting the wire tip, then fasten it and tighten the screw. Be careful not to let the wires stick out ofthe terminal otherwise this may cause a short circuit when wires of different terminal contact each other.
  5. After the unit is turned ON, adjust the main volume to the desired level same with the bass and treble volume, etc.


  • Home Theater Pro Audio Receiver
  • High-Powered Hybrid Pre-Amplifier
  • Multi-Channel Source Audio Selection
  • Built-in BT for Wireless Music Streaming
  • Includes (2) UHF Wireless Handheld Microphones
  • FM/AM Radio with Digital LCD Display
  • USB Flash & SD Memory Card Readers
  • MP3 Audio File Playback Support
  • Connect & Stream Audio from External Devices
  • Aux (3.5mm) Input Jack
  • (2) 1/4’’ Microphone Inputs
  • Headphone Jack, 1/4’’
  • RCA (L/R) Audio Input/Output Jacks
  • Dedicated for Subwoofer Output
  • Screw-Type Speaker Terminal Binding Posts
  • Front Panel Button & Rotary Control Center
  • Independent Audio Source Selection
  • LED Backlight Illumination with Dimmer Control
  • Microphone Volume/Echo Control
  • Integrated Overload & Short Circuitry Protection
  • Built-in Cooling Fan
  • Universal Rack Mount Design

What’s in the Box

  • Hybrid Pre-Amplifier
  • (2) UHF Wireless Handheld Microphones
  • Detachable Rack-Mount Brackets
  • FM/AM Antenna/Wireless BT Antenna
  • Remote Control
  • Power Cable

Wireless BT Connectivity

  • Built-in Receiver for Wireless Audio Music Streaming
  • Simple & Hassle-Free Pairing
  • Works with All of Today’s Latest Devices
    (Smartphones, Tablets, Laptops, Computers, etc.)
  • Wireless BT Version: 5.0
  • Wireless BT Network Name: ‘PYLE PRO’
  • Wireless Range: 40’+ ft.

Technical Specs

  • Power Output: 3000 Watt MAX
  • 900 Watt @ 2 Ohm
  • 450 Watt @ 4 Ohm
  • 300 Watt @ 8 Ohm
  • Frequency Response: 40Hz-15kHz, +/-2dB
  • S/N Ratio: >76dB
  • T.H.D.: <1%
  • Radio Station Memory Presets: 30
  • Digital Media File Playback Support: MP3/WMA/WAV/FLAC/APE
  • Maximum USB/SD Flash Memory Support: Up to 64GB
  • Battery Operated Remote: Requires (2) *LR03/1.5V Batteries, Not Included
  • Battery Operated Mic, Requires (2) x ‘AAA’ Batteries Each, Not Included
  • Power Cord Length: 4.5’ ft.
  • Power Supply: 115/230V, Switchable
  • Unit Dimensions (L x W x H): 19.0’’ x 12.0’’ x 3.1’’ –inches




This Post Has 2 Comments

  1. Mark LePoudre

    How do I get the A and B speakers to play at the same time or alternately? There does not seem to be a switch for this.

    1. admin

      Hello Mark,

      If you’ve checked the manual and there is no specific mention of a switch or function to control the speakers in that manner, it’s likely that the amplifier does not support such a feature. Some amplifiers and receivers have the ability to play speakers in different configurations, like A/B or A+B, but not all models offer this capability.

      To be sure about the available options for your specific model, I recommend checking the manual thoroughly or contacting PYLE customer support directly. They will be able to provide you with the most accurate information regarding the capabilities of your amplifier and whether there is a way to achieve simultaneous or alternating playback between A and B speakers.

Leave a Reply