Shark Intelligent Steam Control User Manual

Shark Intelligent Steam Control

IMPORTANT SAFETY INSTRUCTIONS

HOUSEHOLD USE ONLY

READ ALL INSTRUCTIONS BEFORE USE

This steam mop has a polarized plug (one blade is wider than the  other).  As  a  safety  feature,  this  plug  will  fit  into  a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature. It is not recommended to use an extension cord with this product.

WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

GENERAL WARNINGS

WHEN USING YOUR SHARK® STEAM & SCRUB, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

1. DONOT leave the steam mop unattended when plugged  ALWAYS unplug the power cord from the electrical outlet when not in use and before servicing.
2. DO NOT use with damaged cord or plug. If steam mop is notworking as it should or has been dropped, damaged, left outdoors, or dropped into water, return it to SharkNinja Operating LLC for examination and repair. Incorrect reassembly or repair can cause a risk of electrical shock or injury when the steam mop is
3. To protect against a risk of electric shock, DONOT immerse the steam mop in water or any other liquids.
4. DONOT handle the plug or steam mop with wet hands or operate it without wearing
5. DO NOT pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. DO NOT run steam mop over cord. Keep cord away from heated
6. DONOT unplug by pulling on power  To unplug, grasp the plug not the power cord. DO NOT use extension cords or outlets with inadequate current-carrying capacity.
7. Unplug before
8. ALWAYSmake sure the steam mop is UNPLUGGED when not in
9. NEVERfill the steam mop or attach the mop head when the steam mop is plugged into an electrical  Unplug from the electrical outlet and allow to cool before you fill the mop, or attach or remove the head.
10. Whencleaning the exterior of the steam mop, unplug the power cord from the electrical outlet and clean the steam mop with a dry or damp  DO NOT pour water or use alcohol, benzene, or paint thinner on the steam mop.
11. To avoid circuit overload, DO NOT operate another applianceon the same socket (circuit) as the steam
12. To avoid scalding injuries, ALWAYS unplug and allow the steam mop to cool before removing or changing mop heads,accessories, or Dirt Grip® pads.
    USE WARNINGS
13. Whenin use, NEVER turn the steam mop over on its side or direct steam toward people, pets or
14. Use the system only for its intended
15. DO NOT use for space-heating
16. DO NOT use
17. DO NOT allow the steam mop to be used by Close attentionis necessary when used near children, pets, or plants.
18. Useonly as described in this owner’s
19. Use only manufacturer’s recommended
20. DONOT put any objects into the steam nozzle  Discontinue use if the steam nozzle is blocked.
21. DONOT put hands or feet under the steam  It gets very hot.
22. Use ONLY on flat, horizontal surfaces. DO NOT use on walls, counters, or
23. DO NOT use on leather, wax-polished furniture, synthetic fabrics, velvet, or other delicate, steam-sensitive
24. DONOT add cleaning solutions, scented perfumes, oils, or any other chemicals to the water used in the steam mop as this may damage it or make it unsafe for  If you live in a hard-water area, we recommend using distilled water in your steam mop.
25. NEVERleave any Dirt Grip® pads in one spot while using or storing for an extended period, as this may damage your surfaces.
26. Youcan release the Dirt Grip® pads after you have unplugged the steam mop and allowed it to
27. Extremecaution should be exercised when using the steam mop to clean
28. NEVERuse steam mop without the Dirt Grip® pads
29. Keep your work area well
30. Store steam mop indoors in a cool, dry
31. Keephair, loose clothing, fingers, and all parts of body away from openings and moving
32. DO NOT carry the steam mop while in
33. The steam emitted from the steam mop is very hotand may cause  Please use caution when using the steam mop.
34. DO NOT use on unsealed wood or unglazed ceramic floors. Onsurfaces that have been treated with wax and on some unwaxed floors, the sheen may be removed by the heat and steam action.
35. ALWAYS test an isolated area of the surface to be cleaned before We also recommend that you check the use and care instructions from the floor manufacturer.
36. DO NOT scrub any one area for an extended
37. DO NOT use the steam mop without attaching the Dirt Grip®pads and adding water to the water tank. When you use the steam mop for the first time, it might take longer than the normal 30 seconds to start
38. DO NOT use on unsealed wood or unglazed ceramic floors. Onsurfaces that have been treated with wax and on some unwaxed floors, the sheen may be removed by the heat and steam action. Test an isolated area of the surface to be cleaned before proceeding. Check the use and care instructions from the floor
39. To prolong the life of your steam mop, we recommend using distilled water. Add ONLY water to the tank. Chemicals or cleaning solutions (including vinegar) may damagethe steam mop and could be unsafe for you and your family.
40. The liquid or steam must not be directed towards equipmentcontaining electrical components, such as the interior of ovens.

READ AND SAVE THESE INSTRUCTION

Scan Here:
Visit: sharkclean.com/support

Ordering Additional Accessories: You can purchase replacement Dirt Grip® pads, dusting pads, and other accessories by visiting sharkclean.com.

STEAM MOP ASSEMBLY

1. Insert the handle into the mop bodyuntil it clicks into place. (fig. 1)
2. Place pads on the floor with the rings facing up. Align the mop head so the indents on the rotating discs are directly above the rings, then lower the head onto the pads, pressing until secure. (fig. 2).

USING YOUR STEAM MOP

1. Sweep or vacuum floors before mopping.
2. Plug in unit and recline handle.
3. Press the Mode button to select a setting. The pads will start spinning. Wait 30 seconds for the unit to begin producing steam.
4. Mop with a forward and backward motion.
5. When finished mopping, press the Mode button until in Standby; the lights will blink.
6. Lift the handle to stand mop upright, then unplug cord. Allow mop to cool completely (2 – 3 mins), then pull pads off discs.

NEVER leave the steam mop with damp or wet pads on any floor for an extended period.

STEAM BLASTER

1. To target tough messes with an extra burst of cleaning power, move the front of the nozzle 2 to 4 inches from the mess, then press and hold the Steam Blaster® button as needed. (Hold longer for the toughest messes.)
2. Before scrubbing, wait 5 seconds to let the steam blast penetrate the mess.

Tip: For more difficult messes, allow 20 seconds or more.
Note: While the Steam Blaster is blasting steam, steam does not also emit from the pads.

AFTER USE AND STORAGE

1. Press the mode button until the indicator lights below start to blink, indicating that you are in Standby mode. Unplug the cord from the outlet and place the steam mop into the upright position. Let it cool. (fig. 3)
2.  When the pads have cooled completely, remove them by pullingthem off the discs. (fig. 4)
3. After the unit has cooled and the steam has been released, empty the water tank before storing. Open the tank lid and pour the water out into a sink or bathtub. After all the water has drained out, close the lid.
4. To store the steam mop, wait until after it has cooled and the steam has been released. Store steam mop in a dry, protected area until next use.

ONE (1) YEAR LIMITED WARRANTY

The One (1) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable.

SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period of one (1) year from the date of purchase when it is used under normal household conditions and maintained according to the requirements outlined in the Owner’s Guide, subject to the following conditions and exclusions:

What is covered by this warranty?

1. Theoriginal unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to one (1) year from the original purchase
2. In the event a replacement unit is issued, the warranty coverageends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater

What is not covered by this warranty?

1. Normal wear and tear of wearable parts (such as Shark Cleaner,Pad, ), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damagecaused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure to perform required maintenance, or damage due to mishandling in
4. Consequential and incidental
5. Defects caused by repair persons not authorized by These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.
6. Productspurchased, used, or operated outside North

How to get service

If your appliance fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/support for product care and maintenance self- help. Our Customer Service Specialists are also available at

1-800-798-7398 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. So we may better assist you, please register your product online at

registeryourshark.com and have the product on hand when you call.

SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $25.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.

How to initiate a warranty claim

You must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase. We also ask that you register your product online at registeryourshark.com and have the product on hand when you call, so we may better assist you. A Customer Service Specialist will provide you with return and packing instruction information.

How state law applies

This warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

 DOWNLOAD LINK

Shark Intelligent Steam Control User Manual

https://www.sharkclean.com/

https://support.sharkclean.com/hc/en-us/article_attachments/5981315685020/S7001Series_QSG_Sheet_MP_Mv2_LR.pdf