SONY XAV-AX8100 Digital Media Receiver User Manual

SONY XAV-AX8100 Digital Media Receiver User Manual

Warning

The nameplate indicating operating voltage, etc., is located on the bottom of the chassis. The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area) and Switzerland.

FOR THE CUSTOMERS IN THE USA. NOT APPLICABLE IN CANADA, INCLUDING IN THE PROVINCE OF QUEBEC.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Do not ingest battery, Chemical Burn Hazard

The remote commander contains a coin/ button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Note on the lithium battery
Do not expose the battery to excessive heat such as direct sunlight, fire or the like.

Disclaimer regarding services offered by third parties
Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations.

Important notice

Dear customer, this product includes a radio transmitter. Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle.

Emergency calls
This BLUETOOTH car is hands-free and the electronic device connected to the hands-free operates using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies).

On BLUETOOTH communication

• Microwaves emitting from a BLUETOOTH device may affect the operation of electronic medical devices. Turn off this unit and other BLUETOOTH devices in the following locations, as it may cause an accident.
  • where inflammable gas is present, in a hospital, train, airplane, or petrol station
  • – near automatic doors or a fire alarm
• This unit supports security capabilities that comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using BLUETOOTH wireless technology.
• We do not take any responsibility for the leakage of information during BLUETOOTH communication.

If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.

Main Unit and Remote Commander

Main unit 

The VOL (volume) + button has a tactile dot

1. Display/touchscreen
2. HOME Displays the HOME screen. STANDBY Press and hold to turn the unit to standby mode (USB charging is still available). To resume, press any button.
3. VOL (volume) +/–
4. ATT (attenuate) Attenuates the sound. To cancel, press again, or press VOL +. MONITOR OFF Press and hold to turn off the monitor. To turn it back on, touch any part of the display.
5. Receptor for the remote commander
6. OPTION Displays the OPTION screen.
7. (previous/next) Functions differently depending on the selected source:
   • [Radio]: select a preset station. [SXM]
   • (SiriusXM): select a preset channel.
   • [USB]/[Bluetooth]: move to the previous/next file.
     Press and hold to:
   • [Radio]: tune into a station automatically (SEEK+/SEEK–).
   • [USB]/[Bluetooth]: fast-reverse/fast-forward.
8. VOICE Activates the voice command function for Apple CarPlay and Android Auto™.
9. HDMI terminal (input)
   RM-X170 remote commander
   The remote commander can be used to operate the audio controls. For menu operations, use the touch screen.
   
10. OFF Turns the source off.
11. MONITOR OFF Turns off the monitor. To turn it back on, press again.
12. EQ (equalizer) Selects an equalizer curve.
13. Number buttons (0 to 9)
14. CLEAR
15. ATT (attenuate) Attenuates the sound. Press again to cancel the attenuation.
16. (play/pause)
17. (previous/next)
    (fast-reverse/fast-forward) Functions differently depending on the selected source:
    • [Radio]: select a preset station.
    • [SXM] (SiriusXM): select a preset channel.
    • [USB]/[Bluetooth]: move to the previous/next file.
      Press and hold to:
    • [Radio]: tune into a station automatically (SEEK+/SEEK–).
    • [USB]/[Bluetooth]: fast-reverse/fast-forward
18. Functions differ depending on the selected source. –
    • [Radio]: select a preset station or tune into a station automatically.
    • [SXM] (SiriusXM): select a preset channel or move to the previous/next channel.
    • [USB]: select a folder or move to the previous/ next file
      TER
      Enters the selected item.
19. SRC (source) Changes the source. Each time you press this button, a selectable source is displayed in a popup on the current display.
20. MODE Selects the radio band.

Remove the insulation film before use.

Screen Displays

Playback screen:

HOME screen: 

OPTION screen: 

1. Status indication
   
2. (source option) Opens the source option menu. The available items differ depending on the source.
3. Application-specific area Displays playback controls/indications or shows the unit’s status. Displayed items differ depending on the source.
4. The clock Displays the time which is set on the Date/ Time setting.
5. (instruction for smartphone connection) Displays the instructions for connecting Apple CarPlay, Android Auto, or WebLink™
6. (return to the playback screen) Switches from the HOME screen to the playback screen.
7. Sources and Settings select keys Change the source or make various settings. Flick to select the setting icon and other icons. Touch the source icon you want to select.
   
8. Sound select keys Change the sound.
9. (EXTRA BASS) Changes the EXTRA BASS setting.
10. (EQ10/Subwoofer) Changes the EQ10/Subwoofer setting.
11. (monitor off) Turns off the monitor. When the monitor is turned off, touch any part of the display to turn it back on.

Basic Operations

Pairing with a BLUETOOTH Device
When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other.

1. Press HOME, then touch [Settings] [Bluetooth] [Bluetooth Connection] [ON] [Pairing].flashes while the unit is in pairing standby mode.
2. Perform pairing on the BLUETOOTH device so it detects this unit. 3 Select your model name shown on the display of the BLUETOOTH device*. When pairing is made,stays lit. * If passkey input is required on the BLUETOOTH device, input [0000].

Connecting Rear View Camera
By connecting the optional rearview camera to the CAMERA IN terminal, you can display the picture from the rearview camera. For details, see “Connection/Installation” (page 11). To display the picture from the rear view camera Press HOME, then touch [Rear Camera].

Additional Information

Precautions 

• The power antenna (aerial) extends automatically.
• When you transfer ownership or dispose of your car with the unit installed, initialize all the settings to the factory settings by performing the factory reset.
• Do not splash liquid onto the unit.

Notes on safety

• Comply with your local traffic rules, laws, and regulations.
• While driving
  • Do not watch or operate the unit, as it may lead to distraction and cause an accident. Park your car in a safe place to watch or operate the unit.
  • Do not use the setup feature or any other function that could divert your attention from the road.
  • When backing up your car, be sure to look back and watch the surroundings carefully for your safety even if the rearview camera is connected. Do not depend on the rearview camera exclusively.
• While operating
  • Do not insert your hands, fingers, or foreign objects into the unit as it may cause injury or damage to the unit.
  • Keep small articles out of the reach of children.
  • Be sure to fasten seatbelts to avoid injury in the event of sudden movement of the car.

Preventing an accident
Pictures appear only after you park the car and set the parking brake. If the car starts moving during video playback, the following caution is displayed and you cannot watch the video.

Notes on the LCD panel

• Do not get the LCD panel wet or expose it to liquids. This may cause a malfunction.
• Do not press down hard on the LCD panel as doing so can distort the picture or cause a malfunction (i.e., the picture may become unclear or the LCD panel may be damaged).
• Do not touch the panel with objects other than with your finger as it may damage or break the LCD panel.
• Clean the LCD panel with a dry soft cloth. Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray.
• Do not use the unit outside the temperature range 0 ºC to 40 ºC (32 ºF to 104 ºF).
• If your car was parked in a cold or hot place, the picture may not be clear. However, the monitor is not damaged and the picture will become clear after the temperature in your car becomes normal.
• Some stationary blue, red, or green dots may appear on the monitor. These are called “bright spots” and can happen with any LCD. The LCD panel is precision-manufactured with more than 99.99% of its segments functional. However, it is possible that a small percentage (typically 0.01%) of the segments may not light up properly. This will not, however, interfere with your viewing.

Notes on the touchscreen

• This unit uses a resistive touch screen. Touch the screen directly with your fingertip.
• Multi-touch operation is not supported on this unit.
• Do not touch the screen with sharp objects such as a needle, pen, or fingernail. Operation with a stylus is not supported on this unit.
• Do not let any objects contact the touch screen. If the screen is touched by an object other than your fingertip, the unit may not respond correctly.
• Since glass material is used for the screen, do not subject the unit to strong shock. If cracking or chipping occurs on the screen, do not touch the damaged part as it may cause injury.
• Keep other electrical devices away from the touch screen. They may cause the touch screen to malfunction.

About iPhone 

• Compatible iPhone models: iPhone SE (2nd generation), iPhone 11 Pro Max, iPhone 11 Pro, iPhone 11, iPhone XS Max, iPhone XS, iPhone XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s
• Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an Apple product may affect wireless performance.

Maintenance

Replacing the lithium battery (CR2025) of the remote commander
When the battery becomes weak, the range of the remote commander becomes shorter.

CAUTION
The a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.

Note on the lithium battery
Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor.

Specifications

AUDIO POWER SPECIFICATIONS

• CTA2006 Standard
• Power Output: 20 Watts RMS × 4 at
• 4 Ohms < 1% THD+N
• SN Ratio: 80 dBA (reference: 1 Watt into 4 Ohms)

Monitor section

• Display type: Wide LCD color monitor
• Dimensions: 8.95 in/227 mm
• System: TFT active matrix
• Number of pixels: 1,152,000 pixels (800 × 3 (RGB) × 480)
• Color system: PAL/NTSC automatic select for CAMERA IN terminal

Radio section
FM

• Tuning range: 87.5 MHz – 107.9 MHz
• Usable sensitivity: 7 dBf
• Signal-to-noise ratio: 70 dB (mono)
• Separation at 1 kHz: 45 dB

AM

• Tuning range: 530 kHz – 1,710 kHz
• Sensitivity: 32 μV

USB player section

• Interface:
• USB port: USB (Hi-speed)
• Maximum current: 1.5 A

Wireless communication

• Communication System: BLUETOOTH Standard version 3.0
• Output: BLUETOOTH Standard Power Class 2 (Max. Conducted +1 dBm)
• Maximum communication range*1:
• Line of sight approx. 10 m (33 ft)
• Frequency band: 2.4 GHz band (2.4000 GHz – 2.4835 GHz)
• Modulation method: FHSS

Power amplifier section

• Outputs: Speaker outputs
• Speaker impedance: 4 Ω – 8 Ω
• Maximum power output: 55 W × 4 (at 4 Ω)

General
Power requirements: 12 V DC car battery (negative ground (earth)) Rated current consumption: 10 A Dimensions (maximum): Approx. 229 mm × 136 mm × 253 mm (9 1/8 in × 5 3/8 in × 10 in) (w/h/d) Mounting dimensions: Approx. 182 mm × 53 mm × 160 mm (7 1/4 in × 2 1/8 in × 6 3/8 in) (w/h/d) Mass: Approx. 2.4 kg (5 lb 5 oz) Package contents: Main unit (1) Parts for installation and connections (1 set) Remote commander (1): RM-X170 Optional accessories/equipment: SiriusXM Connect Vehicle Tuner: SXV100, SXV200, SXV300 Ask the dealer for detailed information. Design and specifications are subject to change without notice.

Copyrights

SiriusXM-Ready® allows you to Listen to ad-free music, plus all the sports, talk, comedy, news coverage, all in one place. (SiriusXM Connect Tuner and subscription required. Sold separately.) For more information, visit www.siriusxm.com. Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,

Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners. Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft Corporation.

Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary. Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. Apple CarPlay is a trademark of Apple Inc. Android Auto is a trademark of Google LLC.

WebLink is a registered trademark of Abalta Technologies, Inc. in the U.S. and a trademark in the other countries. The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. All other trademarks are trademarks of their respective owners.

Connection/Installation

Cautions

• Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes a battery drain.
• Run all ground (earth) leads to a common ground (earth) point.
• Do not get the leads trapped under a screw or caught in moving parts (e.g., seat railing).
• Before making connections, turn the car ignition off to avoid short circuits.
• Connect the yellow and red power supply leads only after all other leads have been connected.
• Be sure to insulate any loose unconnected leads with electrical tape for safety.
• Choose the installation location carefully so that the unit will not interfere with normal driving operations.
• Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a safe and secure installation.
• Be sure to use the supplied USB extension cables.
• This unit may not be installed properly depending on the car type. For details on the mounting space.
• To avoid injury, be careful not to drop the display during installation.
• When installing, be careful not to cut off your fingers with the metal parts of the brackets and mounting base.
• Do not pinch your fingers when attaching the display to the unit.
• Do not install the unit in a position where the unit interferes with driving operations (such as in positions where the shift lever hits the unit, or the hazard button cannot be pressed).
• When using the unit for a long period of time, there may be a possibility that the screws securing the display may come loose. Periodically tighten these screws.
• Do not make any changes or modifications to the unit other than those described in this manual.

Note on the power supply lead (yellow)
When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component’s fuse amperage rating. Note on installing in cars with a start-stop system The unit may restart when starting the engine from startstop. In this case, turn off the start-stop system of your car.

Parts List for Installation

This parts list does not include all the package contents.

Connection

• To prevent short circuits, insulate leads with a cover or tape.
• Note that the unit may be damaged if it is connected incorrectly or by short circuits at the leads.

1. Not supplied
2. Speaker impedance: 4 Ω to 8 Ω × 4
3. RCA pin cord (not supplied)
4. Depending on the type of car, use an adaptor for wired remote control (not supplied). For details on using the wired remote control,
5. Depending on the type of car, use an adaptor (not supplied) if the antenna (aerial) connector does not fit.
6. Whether in use or not, route the microphone input cord so it does not interfere with driving operations. Secure the cord with a clamp, etc., if it is installed around your feet.
7. For details on installing the microphone,
8. For more information on how to install the SiriusXM Connect Vehicle Tuner, consult the installation guide included with the tuner.
9. 
10. When using the steering wheel remote control, use the connection cable RC-SR1 (8) as necessary.

Making connections

1. To a common ground (earth) point First connect the black ground (earth) lead then connect the yellow and red power supply leads.
2. To the +12 V power terminal which is energized at all times Be sure to first connect the black ground (earth) lead to a common ground (earth) point.
3. To the +12 V power terminal which is energized when the ignition switch is set to the accessory position Be sure to first connect the black ground (earth) lead to a common ground (earth) point.
4. To the power antenna (aerial) control lead or the power supply lead of the antenna (aerial) booster, It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers and a power antenna (aerial). Connecting any other system may damage the unit. Note It will take about 10 seconds to shut down the output of REM OUT after the unit is turned off.
5. To a car’s illumination signal Be sure to first connect the black ground (earth) lead to a common ground (earth) point.
6. To the parking brake switch lead The mounting position of the parking brake switch lead depends on your car. Be sure to connect the parking brake lead (light green) of the power supply leads (1) to the parking brake switch lead.
   
7. To the +12 V power terminal of the car’s rear lamp lead (only when connecting the rearview camera)

Speaker connection

• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.

Installing the microphone

To capture your voice during hands-free calling, you need to install the microphone (3).

Cautions

• It is extremely dangerous if the cord becomes wound around the steering column or gearstick. Be sure to keep it and other parts from interfering with your driving operations.
• If airbags or any other shock-absorbing equipment are in your car, contact the store where you purchased this unit or the car dealer before installation.

Before mounting the unit

Before mounting the unit in the dashboard, arrange the USB extension cables.

USB cable connection diagram

1. Remove the cable cover, store the USB extension cable (short) (7) to the groove of the unit, then attach the cable cover. Position the USB cable so that its connector (male) comes to the front side of the unit.
   
2. Route the USB extension cable (long) (6) inside the dashboard, then connect the USB cable (short) (7) from the unit. Position the USB cable so that its connector (male) comes out from the center console panel.

Mounting the unit in the dashboard

Using the mounting brackets supplied with your car
You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer.

Example

Attaching the joint cover

1. Attach the joint cover (11) to the mounting base of the unit, then slide it into the unit temporarily.

Setting up the display

The mounting positions of the display can be adjusted.

Adjusting the depth of the display position 

1. Loosen the 3 pre-installed screws for depth adjustment (on top and both sides).
   
   Slightly loosen the screws until you can slide the connector bracket. Do not remove the screws from the bracket. Doing so may damage the parts.
2. Slide the connector bracket to decide the appropriate depth position. Adjustable depth: within 20 mm (13/16 in) (A), in 3 steps, in 10 mm (13/32 in) pitch (B).
   
3. At the desired position, tighten the 3 screws firmly to secure the connector bracket.
   
   Tighten the screws firmly. When you tighten a screw, be careful not to apply too much torque as doing so may damage the screw (the torque value should be from 1.2 N•m to 1.5 N•m).

Bracket positions 1 to 3 for the display:

1. Slide-out position
2. Intermediate position
3. Slide-in position

Adjusting the height of the display position

1. Remove the 4 pre-installed screws for height adjustment (on both sides)
   
2. Slide the connector bracket up or down to decide the appropriate height position. Adjustable height: within 60 mm (2 3/8 in) (A), in 7 steps, in 10 mm (13/32 in) pitch (B).
   
3. At the desired position, tighten the 4 screws firmly to secure the connector bracket.
   
   Tighten the screws firmly. When you tighten a screw, be careful not to apply too much torque as doing so may damage the screw (the torque value should be from 1.2 N•m to 1.5 N•m).

REFERENCE LINK

https://www.sony.com/ug/electronics/digital-media-receivers-with-touchscreen/xav-ax8100