Kenmore Bagless Upright Vacuum Cleaner User Manual

Kenmore Bagless Upright Vacuum Cleaner User Manual

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions in this guide before assembling or using your vacuum cleaner

WARNING! Your safety is important to us. To reduce the risk of fire, electrical shock, injury to persons or damage when using your vacuum cleaner, follow basic safety precautions including the following:

• Use your vacuum cleaner only as described in this Use & Care Guide.
• Use only manufacturer’s recommended attachments.
• Disconnect electrical supply before servicing or cleaning out the brush area. Failure to do so could result in the brush unexpectedly starting, causing personal injury from moving parts.
• Do not leave vacuum cleaner when plugged in. Unplug from outlet when not in use and before performing maintenance.
• To reduce the risk of electrical shock – Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Do not use with a damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, immediately discontinue use and call 1-877-531-7321 (US) / 1-844-608-3081 (CA) for assistance.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any objects into openings.
• Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not put on chairs, tables, etc. Keep on floor.
• Do not use vacuum cleaner to pick up flammable or combustible liquids (gasoline, cleaning fluid, perfumes, etc.), or use in areas where they may be present. The fumes from these substances can create a fire hazard or explosion.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use vacuum cleaner without dust cup and/or filters in place.
• Always clean the dust cup after vacuuming carpet cleaners or freshener, powders, and fine dust. These products clog the filters, reduce airflow and can cause damage to the vacuum cleaner. Failure to clean the dust cup could cause permanent damage to the vacuum cleaner.
• Do not use the vacuum cleaner to pick up sharp hard objects, small toys, pins, paper clips, etc. They may damage the vacuum cleaner or dust cup.
• You are responsible for making sure that your vacuum cleaner is not used by anyone unable to operate it properly.

SAVE THESE INSTRUCTIONS

Proper assembly and safe use of your vacuum cleaner are your responsibilities. Your vacuum cleaner is intended for Household Use. Read this Use & Care Guide carefully for important use and safety information. This guide contains safety statements under warning and caution symbols.

VACUUM CLEANER WARRANTY

LIMITED WARRANTY

FOR ONE YEAR from the date of sale this product is warranted against defects in material or workmanship. WITH PROOF OF SALE a defective product will be replaced free of charge. The Kenmore brand is used under license. Direct all claims for warranty service to: 1-877-531-7321 (US) / 1-844-608-3081 (CA). This warranty does not cover filters or belts, which are expendable parts that can wear out from normal use within the warranty period. This warranty is void if this product is ever used for other than private household purposes. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Cleva North America, Inc., Greenville SC 29607

PARTS AND FEATURES

It is important to know your vacuum cleaner’s parts and features to assure its proper and safe use. Review these before using your vacuum cleaner

REPLACEMENT PARTS

Item Part No.(US) Part No.(CA)
Foam Filter 561055105 561055105
Felt Filter 561055106 561055106
Exhaust Filter 571017106 571017106
3-in-1 Combination Tool 561055134 561055134
Extension Wand 561055128 561055128
Flexible Hose 571017110 571017110
Screw Bolt 561072105 561072105

To order a replacement part, call 1-877-531-7321 (US) / 1-844-608-3081 (CA)

Please pay special attention to these hazard alert boxes, and follow any instructions given. WARNING statements alert you to such hazards as fire, electric shock, burns and personal injury. CAUTION statements alert you to such hazards as personal injury and/or property damage.

ASSEMBLY INSTRUCTIONS

Before assembling the vacuum cleaner, check the PACKING LIST (page 2). Use this list to verify that you have received all the components of your new Kenmore Bagless Upright Vacuum Cleaner.

• Insert the handle into the main body and secure with one screw bolt provided.

NOTE: Tighten the screw bolt with a screwdriver or a coin. Ensure that the screw bolt is secured.

• Insert the larger end of the extension wand into the top of the connection hose through the bracket until the wand is fully seated on the post.

• Insert the end of the flexible hose into the main body by aligning marks as shown in UNLOCKED (for cleaning). Rotate the hose until marks align as shown in LOCKED (for use). Then run the flexible hose over the lower hose storage and the upper hose storage. Insert the other end onto the top of the extension wand.

• Insert the combination tool onto the accessory storage post located on the back of the main body.

• Make sure the upper and lower cord hooks are in the proper position as shown. Wrap the power cord loosely around the upper and lower cord hooks.

NOTE: Make sure to wrap the power cord around the upper cord hook first, and then around the lower cord hook to avoid damaging the power cord.

• Lock power cord plug onto the power cord.

WARNING Electrical Shock and Personal Injury Hazard.

Wrapping the cord too tightly with excessive stress on the cord may cause cord damage. A damaged cord is an electrical shock hazard and could cause personal injury or damage.

OPERATING INSTRUCTIONS

CAUTION Moving parts! To reduce the risk of personal injury, DO NOT touch the brushroll when vacuum is on. Contacting the brushroll while it is rotating can cut, bruise or cause other injuries. Always turn off before servicing. Use caution when operating near children or pets.

POWER CORD – RELEASE & USE 

• Turn the upper cord hook to either side to release the power cord.

WARNING

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way

• Detach the power cord plug from the power cord.
• Be sure the power cord is locked into the upper locking notch as shown. This will help manage the power cord when operating the vacuum cleaner.

• Plug the power cord plug into an outlet located near the floor.

WARNING Personal Injury and Product Damage Hazard

• When any abnormality/failure occurs, stop using the product immediately and disconnect the power plug.
• DO NOT use outlets above counters. Damage from cord to items in surrounding area could occur.

• Press the On/Off switch to turn the vacuum cleaner on.
• Once you have completed vacuuming, press the On/Off switch; unplug the power cord plug from the outlet.
• To restore power cord after use, turn the upper cord hook to the upright position. Then wrap cord loosely around cord hooks.

WARNING Electrical Shock and Personal Injury Hazard

Wrapping the cord too tightly puts stress on the cord and can cause cord damage. A damaged cord is an electrical shock hazard and could cause personal injury or damage.

OPERATION MODES

UPRIGHT MODE

NOTE: Make sure the vacuum cleaner is completely assembled and the dust cup is empty before using. Do not operate vacuum cleaner without filters in place.

• Release the handle by placing foot on the nozzle and pull back to change handle position.

• Turn on the vacuum cleaner by pressing the On/Off switch to the “I” position for cleaning bare floors and small area rugs.

NOTE: The brushroll does not rotate when the vacuum cleaner is in the “I” position.

• Press the switch to the “II” position for cleaning carpets or rugs.

NOTE: The brushroll rotates when the vacuum cleaner is in the “II” position.

CAUTION Do not allow the vacuum cleaner to remain in one spot for any length of time when the brushroll is turning. Damage to carpet may occur.

• Once you have completed vacuuming, switch to the “O” position and unplug the power cord from the power outlet.

NOTE: Select the right mode when using this vacuum cleaner. Do not press the switch to the “II” position when cleaning the bare floor, otherwise it could potentially damage the floor.

BRUSHROLL INDICATOR LIGHT

Light Color Status Green, Continuous The brushroll is spinning and working as it should. Red, Continuous There is a jam in the brushroll area. Turn off and unplug the vacuum, and remove any blockages in the nozzle. No Light The brushroll is off

ABOVE FLOOR MODE

• Place the vacuum cleaner in the upright locked position.
• Pull up to release the flexible hose for above floor cleaning.

• Choose the desired extension wand/ attachments and insert it into the flexible hose.

• Turn on the vacuum cleaner by pressing the switch to the “I” position.
• Once you have completed vacuuming, switch to the “O” position and unplug the power cord from the power outlet.

CAUTION When using attachments, be careful not to over extend the flexible hose when reaching. Trying to reach beyond the hose stretch capability could cause the vacuum cleaner to tip over.

• DO NOT pull the vacuum cleaner around the room by the hose. Property damage or personal injury could result.

ATTACHMENTS

3-IN-1 COMBINATION TOOL

• The 3-in-1 combination tool can be attached to the end of the flexible hose and the extension wand. Slide the collar of the tool over the open end of the hose or wand.
• Use the 3-in-1 combination tool in crevice tool mode for cleaning in tight spaces such as furniture, between cushions, and stairs. See ATTACHMENT USE TABLE (page 13).

• Set the combination tool in dusting brush mode by pressing the release button and sliding the dusting brush side of the brush tool to the end of the combination tool. Use in dusting brush mode for cleaning loose surfaces such as drapes. See ATTACHMENT USE TABLE (page 13).

• Press the release button to remove the brush tool. Set the combination tool in upholstery brush mode as shown. Use in upholstery brush mode for cleaning fabric surfaces such as fabric sofa. See

• To return the combination tool to crevice tool mode, press the release button and slide the brush tool down the combination tool.

CAUTION Use attachments when the vacuum cleaner is upright.

ATTACHMENT USE TABLE

PERFORMANCE/SAFETY FEATURES

THERMAL PROTECTOR

• This vacuum cleaner has a thermal protector which automatically trips to protect the vacuum cleaner suction motor.
• If a clog prevents the normal flow of air to the motor, the thermal protector turns the motor off automatically. This allows the motor to cool in order to prevent possible damage to the vacuum cleaner.
• To reset thermal protector: Turn the vacuum cleaner off and unplug the power cord from the outlet to allow the vacuum cleaner to cool and the thermal protectors to reset.

CAUTION Always return the vacuum cleaner to the upright position before using the hose and attachments. Failure to do so may result in overheating of the brushroll motor and can cause the thermal protectors to trip.

• Check for and remove clogs, and empty dust cup if necessary. Also check and replace any clogged filters. Wait approximately 50 minutes before restarting vacuum cleaner.

BRUSHROLL RESET

• The brushroll has built-in protection against motor damage should the brushroll jam.
• If the brushroll slows down or stops, the brushroll overload protector shuts off the brushroll motor and the brushroll indicator light emits red light. The vacuum cleaner suction motor will continue to run.

• To correct problem: Turn off and unplug the vacuum cleaner, remove obstruction, then turn on the vacuum cleaner.

NOTE: Once the brushroll motor shuts down, clear jam from the brushroll before resetting.

• If the problem persists, contact the vacuum cleaner help line for assistance.

SUCTION CONTROL

The suction control allows you to change the vacuum cleaner suction for different fabric and carpet weight

• Rotate to “+” to increase suction on bare floors.
• Rotate to “ ” to reduce suction and increase maneuverability on carpets.

VACUUM MAINTENANCE AND CARE

Always follow all safety precautions when performing maintenance to the vacuum cleaner.

WARNING Electrical Shock and Personal Injury Hazard

Disconnect electrical supply before servicing or cleaning the vacuum cleaner. Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting.

CLEANING EXTERIOR AND ATTACHMENTS

• Turn off and unplug vacuum cleaner. DO NOT drip water on vacuum cleaner.
• To clean exterior, or to reduce static electricity and dust build-up, wipe outer surface with a clean, soft cloth that has been dipped in a solution of mild liquid detergent and water, then wrung dry. Wipe dry after cleaning.

NOTE: Wash attachments in warm soapy water, rinse and air dry. Do not clean in dishwasher

CAUTION Do not use attachments if they are wet. Attachments used in dirty areas, such as under a refrigerator, should not be used on other surfaces until they are washed. They could leave marks.

VACUUM CLEANER STORAGE

WARNING Electrical Shock and Personal Injury Hazard

Wrapping the cord too tightly puts stress on the cord and can cause cord damage. A damaged cord is an electrical shock hazard and could cause personal injury or damage.

• Replace flexible hose and attachments in storage position if necessary (see page 7 & 8).
• Gather the cord and wrap it loosely around the upper and lower cord hooks. Lock plug retainer onto the power cord.
• Store the vacuum cleaner in a dry, indoor area, on the floor with the handle locked in the upright position.

EMPTYING DUST CUP

WARNING
Always unplug power cord from electrical outlet before performing any service on vacuum cleaner.

NOTE: For best performance, empty dust cup after every use. Never operate vacuum cleaner without dust cup and filters in place.

• Slide the dust cup release button to remove the dust cup from the main body

• Remove any clogs that might be located in the suction port

• Position dust cup area of vacuum over a waste receptacle. Press down on the dust release button to open dust cup lid and allow contents to drop into waste receptacle.

• Shake the dust cup to release any debris that might hang in the pre-filter.
• Reinstall and insert the dust cup into the slots on the bottom of the main body, then press the dust cup into locked slot and click into place.

PRE-FILTER CLEANING

The pre-filter is located inside the dust cup. Clean the pre-filter as needed to optimize suction power. If suction remains weak after tapping the pre-filter clean, it will be necessary to wash it to clean off accumulated dust or hair. It is also recommended to wash the pre-filter every three months. See wash instructions in the NOTE to step 4.

• Remove the dust cup as outlined in the EMPTYING DUST CUP (page 16).

NOTE: Make sure dust cup is free of debris before opening.

• Press the dust cup lid release button, and open the lid.

• Grasp pre-filter and rotate counterclockwise as shown to remove.

• Clean pre-filter by gently tapping over a trash container. Tap on several sides to ensure best cleaning.

NOTE: If necessary, rinse with cold water only, DO NOT use detergent or soap. Allow parts to dry 24 hours before putting back into vacuum cleaner.

• DO NOT wash in the dishwasher.
• DO NOT install damp.
• Place the pre-filter back into the dust cup. Grasp pre-filter and rotate clockwise to lock into place.
• Reinstall the dust cup into the main body. See installation instructions in the EMPTYING DUST CUP (page 16)

FOAM AND FELT FILTERS CLEANING

It is recommended to clean the foam and felt filters with cold water every three months.

NOTE: When the cleaning of filters no longer restores vacuum cleaner suction to full power, or the filters are worn or broken, replace the filters. To purchase filters, call 1-877-531-7321 (US) / 1-844- 608-3081 (CA). Regularly clean and replace the filters to keep the vacuum’s suction power optimal.

• Remove the dust cup as outlined in the EMPTYING DUST CUP (page 16).
• Remove the foam and felt filters

• Wash with cold water only, DO NOT use detergent or soap. Squeeze by hand and allow to air dry. Allow all filters to dry 24 hours before putting back into vacuum cleaner.

NOTE: DO NOT operate without foam and felt filters installed.

• DO NOT wash in the dishwasher.
• DO NOT install foam and felt filters if damp.
• Replace foam and felt filters into the vacuum cleaner

TROUBLESHOOTING

Review this table to find do-it-yourself solutions for minor performance problems. Any service needed, other than maintenance described in this Use & Care Guide, should be performed by a qualified service agent.

WARNING Disconnect electrical supply before performing maintenance to the vacuum cleaner. Failure to do so could result in electrical shock or personal injury.

PROBLEM

• Vacuum cleaner will not run.
• Poor job of dirt pick-up

POSSIBLE CAUSE

• Unplugged at wall outlet.
• To start the vacuum cleanpressed
• The vacuum body is overheated.
• The motor is damaged.
• Defective wall outlet.
• Full or clogged dust cup.
• Filters need cleaning.
• The brushroll or belt is worn or broken.
• The flexible hose is worn.
• The connection hose is worn.
• The foam and felt filters are dirty or worn.
• There is a clog in the flexible hose or connection hose of the vacuum cleaner.
• Dust cup is not installed well.
• The hose or attachments are not installed well.

SOLUTION

• Plug in firmly, press the On/Off switch to “I” or “Il” position.
• Press the On/Off switch to “I” or “Il” position.
• Unplug the power cord and let the vacuum cool down for 50 minutes.
• Call 1-877-531-7321 (US) / 1-844-608-3081 (CA) for assistance.
• Check with a good appliance or lamp. Be sure the power cord plug is fully plugged into a good wall outlet
• Empty the dust cup (page 16).
• Follow filter cleaning instructions on page 17-19.
• Call 1-877-531-7321 (US) / 1-844-608-3081 (CA) for assistance.
• Replace the hose. To purchase parts, call 1-877-531-7321 (US) / 1-844-608-3081 (CA).
• Call 1-877-531-7321 (US) / 1-844-608-3081 (CA) for assistance.
• Clean the foam and felt filters. Replace if they are worn or broken. Follow instructions on page 18.
• Check and remove all clogs. Follow instructions on page 20.
• Check dust cup for correct installation and ensure it is snapped firmly in place.
• Check the hose and attachments for correct installation and ensure they are snapped firmly in place.

REFRENCE LINK

https://www.kenmore.com/products/floor-care/vacuum-cleaners/upright-vacuums/