Kenmore BU4050 Intuition Bagged Upright Vacuum Manual

Kenmore BU4050 Intuition Bagged Upright Vacuum Manual

BEFORE USING YOUR NEW VACUUM CLEANER

Read this Use & Care Guide. It will help you assemble and operate your new Kenmore vacuum cleaner most safely and effectively. For more information about vacuum cleaner care and operation, call the Vacuum Cleaner Help Line at 1-844-608-3080 (US) / 1-844-608-3081 (CA). You will need the complete model and serial numbers when requesting information. Your vacuum cleaner’s model and serial numbers are located on the Model and Serial Number Plate. Use the space below to record the model number and serial number of your new Kenmore vacuum cleaner.

PACKING LIST
Your KENMORE INTUITION ® BAGGED UPRIGHT VACUUM CLEANER is packaged with the following parts and components assembled separately in the carton:

• 1 Upright Vacuum Cleaner
• 1 Handle
• 1 Wand
• 1 Crevice Tool
• 1 Flexible Hose
• 1 Upholstery Tool
• 1 Pet HandiMate®
• 1 Deluxe Dusting Brush
• 6 Dust Bags (one dust bag is pre-installed in the vacuum)
• 1 Use & Care Guide

IMPORTANT SAFETY INSTRUCTIONS

Read all the instructions in this guide before assembling or using your vacuum cleaner. Your safety is important to us. To reduce the risk of fire, electrical shock, injury to persons, or damage when using your vacuum cleaner, follow basic safety precautions including the following:

• Use your vacuum cleaner only as described in this Use & Care Guide. Use only with the manufacturer’s recommended attachments.
• Disconnect the electrical supply before servicing or cleaning out the brush roll area. Failure to do so could result in the brush roll unexpectedly starting, causing personal injury from moving parts.
• Do not leave the vacuum cleaner when plugged in. Unplug from the outlet when not in use and before performing maintenance.
• To reduce the risk of electrical shock – Do not use it outdoors or on wet surfaces.
• Do not allow it to be used as a toy. Close attention is necessary when used by or near children.
• Do not use a damaged cord or plug. If a vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, immediately discontinue use and call 1-844-608-3080 (US) / 1-844-608-3081 (CA) for assistance.
• Do not pull or carry by cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not handle the plug or vacuum cleaner with wet hands.
• Do not put any objects into openings.
• Do not use any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
• Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not put on chairs, tables, etc. Keep on the floor.
• Do not use a vacuum cleaner to pick up flammable or combustible liquids (gasoline, cleaning fluid, perfumes, etc.), or use in areas where they may be present. The fumes from these substances can create a fire hazard or explosion.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

SAVE THESE INSTRUCTIONS
Proper assembly and safe use of your vacuum cleaner are your responsibilities. Your vacuum cleaner is intended for Household use. Read this Use & Care Guide carefully for important use and safety information. This guide contains safety statements under warning and caution symbols.

VACUUM CLEANER WARRANTY

LIMITED WARRANTY
FOR ONE YEAR from the date of sale this product is warranted against defects in material or workmanship. WITH PROOF OF SALE a defective product will be replaced free of charge. The Kenmore brand is used under license. Direct all claims for warranty service to 1-844-608-3080 (US) / 1-844-608-3081 (CA). This warranty does not cover filters or belts, which are expendable parts that can wear out from normal use within the warranty period. This warranty is void if this product is ever used for other than private household purposes. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Cleva North America, Inc., Greenville SC 29607

PARTS AND FEATURES

It is important to know your vacuum cleaner’s parts and features to ensure its proper and safe use. Review these before using your vacuum cleaner.

REPLACEMENT PARTS

To order a replacement part, call 1-844-608-3080 (US) / 1-844-608-3081 (CA).

Please pay special attention to these hazard alert boxes, and follow any instructions given. WARNING statements alert you to such hazards as fire, electric shock, burns, and personal injury. CAUTION statements alert you to such hazards as personal injury and/or property damage.

ASSEMBLY INSTRUCTIONS

Before assembling the vacuum cleaner, check the PACKING LIST (page 2). Use this list to verify that you have received all the components of your new Kenmore Intuition® Bagged Upright Vacuum Cleaner.

1. To place the body onto the nozzle, carry the body over the nozzle align the nozzle neck with the guides in the body, and slowly drop into place until a ‘click’ is heard.
   
2. Insert the handle into the wand until you hear a ‘click’.
   
3. Locate the wand parallel with the body; make sure the protrusion is under the upper slot as shown. Then push the wand to fit the body and insert it downward into the nozzle neck. Make sure protrusion I is locked into an upper slot and protrusion II into the lower slot. A ‘click’ can be heard once you finish the wand assembly.
   
   NOTE: DO NOT tilt the wand to insert it into the nozzle neck. DO NOT insert the wand before placing the body onto the nozzle
   
4. Insert the hose into the body until you hear a ‘click’
   
5. Make sure the upper and lower cord hooks are in the proper position as shown. Wrap the power cord loosely around the upper and lower cord hooks.
   NOTE: Make sure to wrap the power cord around the upper cord hook first, and then around the lower cord hook to avoid damaging the power cord.
   
6. Lock the power cord plug onto the power cord.

WARNING
Electrical Shock and Personal Injury Hazard. Wrapping the cord too tightly with excessive stress on the cord may cause cord damage. A damaged cord is an electrical shock hazard and could cause personal injury or damage.

POWER CORD – RELEASE & USE

1. Turn the upper cord hook to either side and down to release the power cord.
   
   WARNING To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
2. Detach the power cord plug from the power cord.
3. Be sure the power cord is locked into the upper locking notch as shown. This will help manage the power cord when operating the vacuum cleaner.
   
4. Plug the power cord into an outlet located near the floor.
5. Press the On/Off button to turn the vacuum cleaner on.
6. Once you have completed vacuuming, press the On/Off button; unplug the power cord plug from the outlet.

OPERATION MODES

UPRIGHT MODE NOTE:
Make sure the vacuum cleaner is completely assembled. Do not operate a vacuum cleaner without a dust bag in place.

1. Release the handle by placing your foot on the nozzle and pulling back to change the handle position.
   
2. Turn on the vacuum cleaner by pressing the On/Off button to clean the bare floor.
   
   NOTE: Your vacuum cleaner has two cleaning modes: one dedicated to bare floors and one for carpets. The vacuum turns on in carpet cleaning mode, which means the brush roll is spinning. To switch to bare floor mode, simply press the Brushroll On/Off button to turn the brushroll off. We do not recommend vacuuming with the brushroll on when cleaning bare floors as this may damage your floor.
3. Press the Brushroll On/Off button to clean carpets.
4. Once the vacuum is on, operate the vacuum cleaner by tilting the wand back towards you and the nozzle is flush with the floor surface.
   
5. Once you have completed vacuuming, press the On/Off button again and unplug the power cord from the power outlet.

AG FILL LEVEL INDICATOR

As the dust bag fills with dirt and debris, an indicator near the wand can be used to estimate the level of bag fill. Once all LEDs are illuminated red, the bag should be replaced.

CAUTION
Make sure the dust bag is replaced when all LED lights begin to illuminate red continuously. If not, the LED lights will flash red. If the red flashing remains after replacing the dust bag, check and clean the air path as it is blocked.

BRUSHROLL STATUS INDICATOR

ATTACHMENTS

All included accessory tools can be inserted into either the handle or the wand.

DELUXE DUSTING BRUSH
Slide the collar of the brush into the open end of the hose or wand. Use a deluxe dusting brush for cleaning loose surfaces such as drapes, furniture, or walls.

UPHOLSTERY TOOL
The upholstery tool can be attached to the end of the handle and the wand. Slide the collar of the tool into the open end of the handle or wand. Use the upholstery tool for cleaning upholstery and fabric surfaces such as sofas and drapes.

CREVICE TOOL
Slide the collar of the crevice tool into the open end of the hose or wand. Use crevice tool for cleaning in tight spaces such as furniture, between cushions, and stairs.

PET HANDIMATE®
The Pet HandiMate® can be attached to the end of the handle and the wand. Pet HandiMate® pivots for more convenient cleaning. Use Pet HandiMate® for cleaning fabric surfaces such as furniture and carpet.

ATTACHMENT USE TABLE

PERFORMANCE/SAFETY FEATURES

THERMAL PROTECTOR
This vacuum cleaner has a thermal protector that automatically trips to protect the vacuum cleaner suction motor. If a clog prevents the normal flow of air to the motor, the thermal protector turns the motor off automatically. This allows the motor to cool to prevent possible damage to the vacuum cleaner.

To reset thermal protector: Turn the vacuum cleaner off and unplug the power cord from the outlet to allow the vacuum cleaner to cool and the thermal protectors to reset. Check for and remove clogs, and replace dust bags if necessary. Also, check and clean any clogged filters. Wait approximately 50 minutes before restarting the vacuum cleaner.

BY-PASS VALVE
This vacuum cleaner has a By-Pass Valve which prevents motor overheating and damage. The valve opens to provide cooling air when a clog prevents normal airflow to the vacuum cleaner suction motor. You will notice a change of sound as air rushes through the valve opening. To correct the problem: remove any clogs, check and replace filters if needed, and check and install a new dust bag if needed. NOTE: The By-Pass Valve may open when using attachments or when cleaning new carpet due to reduced airflow or air path is blocked, caused by the attachments themselves or by new carpet lint filling the dust bag quickly.

HAIR ELIMINATOR™ BRUSHROLL
For best performance, the motorized nozzle is equipped with a hair eliminator™ brushroll, which prevents the build-up of hair, string, and other debris on the brush roll. To remove any hair wrapped around the brushroll, simply continue vacuuming allowing the brushroll to automatically remove the hair wrap and send it to the dust bag.

BRUSHROLL RESET
The brush roll has built-in protection against motor damage should the brushroll jam. If the brushroll slows down or stops, the brush roll overload protector shuts off the brushroll motor and the brushroll status indicator emits red light. The vacuum cleaner’s suction motor will continue to run.

To solve the problem: Turn off and unplug the vacuum cleaner, remove the obstruction, and then turn on the vacuum cleaner. NOTE: Once the brushroll motor shuts down, clear the jam from the brushroll and then restart the vacuum cleaner. If the problem persists, contact the vacuum cleaner helpline for assistance.

SUCTION CONTROL
To assist with the push/pull force of the vacuum on surfaces like thick carpets, the suction control valve can be opened to help reduce suction. Note that for best cleaning results, the suction control valve must be fully closed.

• Slide to the right to open the suction control and decrease suction. Opening control decreases suction for draperies and lightweight rugs.
•  Slide to the left to close the suction control and increase suction. Closing control increases suction for upholstery and carpets.

VACUUM MAINTENANCE AND CARE

1. Turn off and unplug the vacuum cleaner. DO NOT drip water on a vacuum cleaner.
2. To clean the exterior, or to reduce static electricity and dust build-up, wipe the outer surface with a clean, soft cloth that has been dipped in a solution of mild liquid detergent and water, then wrung dry. Wipe dry after cleaning.

CAUTION
Do not use attachments if they are wet. Attachments used in dirty areas, such as under a refrigerator, should not be used on other surfaces until they are washed. They could leave marks.

DUST BAG REPLACEMENT 

1. Pull the bag chamber cover release the handle out and up, and hold the cover using the handle.
   
   NOTE: Do not press the dust bag release button when releasing the bag chamber cover, or the dust bag will drop down automatically.
2. Tilt the bag chamber as shown. Press the Dust Bag Release button and the dust bag drops down automatically.
   
3. To install a new dust bag, insert the dust bag collar into the bracket until you hear a ‘click’, and then rotate bracket down until another ‘click’ can be heard. Tuck the bag into the dust bag chamber. Be sure all sides of the dust bag are flat within the bag chamber.
   
4. Place the tab on the dust bag chamber cover in the slot on the vacuum cleaner. Push the dust bag chamber cover into place until a ‘click’ is heard. NOTE: Make sure the dust bag is locked into place before pushing the dust bag chamber cover. The dust bag chamber cover can’t be assembled successfully if the dust bag is missing or not installed in place.

HEPA MEDIA EXHAUST FILTER CLEANING

It is recommended to clean the HEPA media exhaust filter with cold water every year. NOTE: When the cleaning of the filter no longer restores vacuum cleaner suction to full power, or the filter is worn or broken, replace the exhaust filter. To purchase the exhaust filter, call 1-844-608-3080 (US) / 1-844-608-3081 (CA).

1. Remove the exhaust filter cover by pulling the tab outward at the bottom of the cover

TROUBLESHOOTING

Review this table to find do-it-yourself solutions for minor performance problems. Any service needed, other than maintenance described in this Use & Care Guide, should be performed by a qualified service agent.

WARNING
Disconnect the electrical supply before performing maintenance on the vacuum cleaner. Failure to do so could result in electrical shock or personal injury.

REFERENCE LINK

https://kenmorefloorcare.com/kenmore-intuition-bagged-upright-vacuum-with-hair-eliminator-brushroll-bu4050