Forever RC-300 Buggy Remote Control Car User Guide

Forever logo

Forever RC-300 Buggy Remote Control Car User Guide


Set Includes

  •  Remotely controlled car
  •  Remote
  • Car battery, 2 units
  • Manual
  •  Smartphone handle





  1. Camera HD 720p
  2. Suspension
  3. Smartphone handle
  4. LED
  5. Turning knob – turn left
  6. Turning knob – turn right
  7. Throttle – drive forward
  8. Throttle – drive backwards
  9. Remote switch
  10. Battery socket.
  11. Back drive differential
  12.  Battery cover
  13. Wlacznik
  14. Turning adjustment

Battery Installation

Batteries in the remote

  • Use only 4 x 1.5 V AA batteries.
  • The battery must be installed according to markings in the socket.
  • Do not short-circuit poles of the batteries.
  • Remove the batteries from the remote when it is not used.
  • Insufficient power supply may cause difficulties in controlling the device.
  • Do not throw the batteries into fire. Protect the batteries against overheating.
  • Protect the batteries against mechanical damage.
  • Hand over used batteries to batteries collection points. Do not dispose of batteries and electronics with municipal solid waste.

Installation of batteries in the control remote

  1. Remove the battery cover.
  2.  Install 4 x 1.5 V AA alkaline batteries according to markings in the socket.
  3. Close the battery socket cover and install the screw.

NOTE: Do not use batteries other than those specified in the specification.


Batteries in the car

  • Use only the battery attached to the set.
  • 6 V NI-Cd batteries may ignite spontaneously if they are not used according to recommendations.
  •  Remove the batteries from the car when it is not used.
  •  Rechargeable batteries should be removed from the car before they are charged.
  • The drive time will be reduced when the car and the remote are not charged sufficiently. Insufficient power supply may cause difficulties associated with acceleration and off-road driving.
  •  Do not leave 6 V Ni-CD batteries unattended when they are charging.
  •  In case of problems associated with a battery (overheating, swelling, mechanical damage), immediately disconnect it from a charger.

Car battery charging

  1. Remove the batteries from the car. If the battery is hot – wait a couple of minutes before charging it again.
  2. Connect the battery adapter to 5 V DC power source. As a power source, you may use a wall charger with 1 A or 2 A USB port. Connect the batteries to the charger.
  3. After fully charging, the LED on the adapter will stop flashing and will be lit continuously, disconnect the battery from the charger.

Installation of a battery in the car

  1. Remove the screw securing the battery cover.
  2. Tilt the two hooks of the battery socket.
  3. Insert the battery and connect it to the car using the quick-coupler.
  4. Close the battery socket cover.
  5. Protect the cover by screwing the securing screw in

Preparation for driving

Activate the car using ON-OFF switch located on its bottom. Then, start the remote using ON-OFF switch. When the LED on the remote lights steadily, the device is ready for operation.

Best conditions for driving
Use the car during sunny days and avoid using it on rainy days. Driving in extremely hot or cold days may impact the control over the devices. Using the car in temperatures exceeding 30 Celsius degrees is prohibited, since they may overheat the cell and damage it.

Controlling the car
After turning the car on and activating the remote, the car is ready for driving. In order to drive forward, pull the throttle on the remote in the direction of the remote handle. Driving backwards– push the throttle away from the handle. Wheels are turned by using the knob on the remote, a slight turn changes the position of wheel and makes the car turn in the desired direction. Braking takes place upon releasing the throttle.

Low battery level indication
When the battery is almost depleted, the car will start to slow down. When it happens, dismantle the battery and connect it to a charger.


  •  The product contains small elements. Keep away from small children.
  •  The producer and the supplier will not be held responsible for damage caused by improper use.
  •  Do not use the car in rain or in vicinity of water containers.
  •  Do not leave a charging battery unattended.
  •  Do not charge the battery on a flammable surface.
  • When cleaning, make sure that the car is disconnected from power supply.
  • Do not let the car to fall off from significant heights – this may damage the device.
  • The manual is universal for several models, therefore, there may be slight differences in the description of functions.

Application Instruction

  1.  Open (depending on the system) App Store / Google Play Store and type Buggy RC-300 in the search field
  2.  Download and install the application

Connecting with the car using the application

  1. Activate the car.
  2.  Activate Wi-Fi in the phone.
  3.  Find Wi-Fi “Buggy RC-300” network and connect with it.


Description of the application functions


  1. Show/hide control interface.
  2. Speed mode 1/2.
  3. Gyroscope control mode.
  4. Screen inversion.
  5. VR mode.
  6. Video recording.
  7. Take photo.
  8. Photos and video playing.
  9. Help.
  10. Drive forward.
  11. Drive backwards.
  12. Turn left.
  13. Turn right.
  14. Return to the main menu.

Controlling the car

  1.  Connect the car using the application
  2. Press START button
  3. Activate the control interface.

Now, you can smoothly control the car driving direction.

Gyroscope control
During driving, you may activate gyroscope control function. Then, the user may tilt the phone forwards/backwards/left/right instead of using the direction stick to make the car execute commands provided this way.

VR mode processes image from the camera to an image adapted to cooperate with VR goggles (screen divided into half). After activation of VR mode, insert the phone into the goggles (goggles are not included in the set) and put them on your head.


  • Remote control: radio, 2.4 GHz
  • Built-in FPV Wi-Fi camera with live image transmission
  • Camera resolution: HD 720p
  • Dedicated application: iOS/Android
  • Size: 31.5 x 19.3 x 12 cm
  • Scale: 1:12
  • Charging time: up to 2.5 h
  • Battery: 6 V 500 mAh Ni-Cd
  • Remote batteries: 4 x 1.5 V AA (not included)
  • Driving time: up to 15 min on a single charge
  • Control distance: up to 50 m
  • Suspension: spring type
  • Drive: rear-wheel drive
  • Max speed: 25 km/h


Leave a Reply