Shark S5003D Genius Steam Pocket Mop System Owner Guide
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK® GENIUS™ STEAM POCKET® MOP SYSTEM, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK GENIUS STEAM POCKET MOP SYSTEM.
WARNING: DANGER OF SCALDING. The steam emitted from the Steam Mop is very hot and may cause scalding. Please use caution when using the Steam Mop.
WARNING: KEEP STEAM MOP AWAY FROM CHILDREN.
POLARIZED PLUG:
This Steam Mop has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature. It is not recommended to use an extension cord with this product.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
- When in use NEVER turn the Steam Mop over on its side or direct steam toward people, pets or plants.
- Use the system only for its intended use.
- DO NOT use for space-heating purposes.
- DO NOT use outdoors.
- DO NOT leave the Steam Mop unattended when plugged in. ALWAYS unplug the power cord from the electrical outlet when not in use and before servicing.
- DO NOT allow the Steam Mop to be used by children. Close attention is necessary when used near children, pets, or plants.
- Use only as described in this owner’s guide.
- Use only manufacturer’s recommended accessories.
- DO NOT use with damaged cord or plug. If Steam Mop is not working as it should or has been dropped, damaged, left outdoors, or dropped into water, return it to Shark Ninja Operating LLC for examination and repair. Incorrect reassembly or repair can cause a risk of electrical shock or injury when the Steam Mop is used.
- To protect against a risk of electric shock, DO NOT immerse the Steam Mop in water or any other liquids.DO NOT handle the plug or Steam Mop with wet hands or operate it without wearing shoes.
- DO NOT pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. DO NOT run Steam Mop over cord. Keep cord away from heated surfaces.
- DO NOT unplug by pulling on power cord. To unplug, grasp the plug not the power cord. DO NOT use extension cords or outlets with inadequate current-carrying capacity.
- DO NOT put any objects into the steam nozzle openings. Discontinue use if the steam nozzle is blocked.
- DO NOT put hands or feet under the Steam Mop. It gets very hot.
- Use ONLY on flat, horizontal surfaces. DO NOT use on walls, counters, or windows.
- DO NOT use on leather, wax-polished furniture, synthetic fabrics, velvet, or other delicate, steam-sensitive materials.
- DO NOT add cleaning solutions, scented perfumes, oils, or any other chemicals to the water used in the Steam Mop as this may damage it or make it unsafe for use. If you live in a hard-water area, we recommend using distilled water in your Steam Mop.
- NEVER leave any Dirt Grip™ pad in one spot while using or storing for any period of time, as this may damage your surfaces.
- You can release the Dirt Grip pad after you have unplugged the Steam Mop and allowed it to cool.
- When cleaning the exterior of the Steam Mop, unplug the power cord from the electrical outlet and clean the Steam Mop with a dry or damp cloth. DO NOT pour water or use alcohol, benzene, or paint thinner on the Steam Mop.
- Extreme caution should be exercised when using the Steam Mop to clean stairs.
- NEVER use Steam Mop without the Dirt Grip pad attached.
- Keep your work area well lit.
- Store Steam Mop indoors in a cool, dry place.
- To avoid circuit overload, DO NOT operate another appliance on the same socket (circuit) as the Steam Mop.
- To avoid scalding injuries, ALWAYS unplug and allow the Steam Mop to cool before removing or changing mop heads, accessories, or Dirt Grip pads.
SAVE THESE INSTRUCTIONS
Getting Started
When assembling your Steam Mop there may be a little water in or around the water tank. This is because we test all our Steam Mops before you buy them, so you get a quality Shark® Genius™ Steam Pocket® Mop System.
- Steam Mop Handle
- Quick-Release Cord Holder
- Cord Management Clip
- Filling Flask
- Pad Release Button
- Steam Mop Body
- Water Tank LidSteam Control Button
- Water Tank
- Secondary Release Buttons
- Steam Blaster™ Nozzle
- Genius™ Mop Head
- Dirt Grip™ Pad
- Mop Head Release Button
Assembling Your Steam Pocket® Mop
WARNING: ALWAYS make sure the Steam Mop is UNPLUGGED when not in use. NEVER fill the Steam Mop or attach the mop head when the Steam Mop is plugged into an electrical outlet. Unplug from the electrical outlet and allow to cool before you fill the mop, or attach or remove the head. To prolong the life of your Steam Mop, we recommend using distilled water. Make sure you add only water to the tank. Chemicals or cleaning solutions (including vinegar) may damage the Steam Mop and could be unsafe for you and your family.
STEAM MOP ASSEMBLY
- Insert the mop handle into the Steam Mop body. Push the mop handle in until it clicks into place. (fig.
- Slide the Genius™ Mop Head into the Steam Mop body. Push until it clicks securely into place. (fig. 1) To detach the Genius Mop Head, press the release button and slide off.
- To attach the Dirt Grip™ pad, spread the pad on the floor with the pocket side up. Center the Genius Mop Head above the pad, then press the pad release button on the back of the Steam Mop body (fig. 2a). Both sides of the mop head will drop open (fig. 2b). Slip the mop head’s four corner tabs into the four corner pockets of the pad (fig. 3 and fig. 4). Gently press one side of the mop head to the floor until that side clicks into place (fig. 5). Repeat on the other side (fig. 6).
- Pull down on the water tank lid to open (fig. 7).
- Use the filling flask to pour water into the tank (fig. 8). Water can be poured into the tank directly. DO NOT overfill past the water line on the fill flask. Press the water tank lid firmly to close it.
Using Your Steam Pocket® Mop
IMPORTANT: Make sure you DO NOT use the Steam Mop without attaching a Dirt Grip™ pad and adding water to the water tank first. When you use the Steam Mop for the first time, it might take longer than the normal 30 seconds to start steaming.
IMPORTANT: DO NOT use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax and on some no-wax floors, the sheen may be removed by the heat and steam action. Test an isolated area of the surface to be cleaned before proceeding. Check the use and care instructions from the floor manufacturer.
NOTE: To prolong the life of your Steam Mop, we recommend using distilled water.
NOTE: Sweep or vacuum your floors prior to cleaning with your Steam Mop.
- Twist the Quick-Release Cord Holder to unwrap the power cord completely (fig. 9). Plug into an electrical outlet.
- When it’s first plugged in, the unit will be in Standby mode. The 3 lights below the Steam Control Button will blink to indicate Standby mode.
- To select the steam mode, press the Steam Control Button once for LOW (1 blue light) twice for MED (2 blue lights) or three times for HI (3 blue lights).
- Clean your floors with a forward and backward motion.
- When you need an extra burst of steam to clean a stuck-on stain, you can use the Steam Blaster™ feature. Flip the head over so that it is behind the mop body, then tilt the mop handle down. This will cause the Steam Blaster (fig. 10) to emit a concentrated blast of steam onto the stain.
CAUTION: While in Steam Blaster mode, DO NOT leave stationary for more than one minute.
CAUTION: DO NOT scrub any one area for an extended period of time.
- To stop the Steam Blaster spray, simply raise the handle. You can then flip the mop head back into its original position and continue cleaning.
- When finished mopping, press the Steam Control Button. The blue light will blink, indicating that the unit is in Standby mode. Once in Standby mode, unplug the unit.
- To remove the Dirt Grip pad, simply lift the mop straight up by the handle until the Genius™ Mop Head is hanging straight down. Press the Release button on the back of the mop body (fig 11a), and both sides of the head will drop open, releasing the pad (fig 11b).
- Once the Dirt Grip pad has been released, close the Genius Mop Head. To close, gently press one side of the Genius Mop Head to the floor until that side clicks into place. Repeat on the other side.
- When the water tank is empty, the Steam Mop will stop producing steam. You can refill the water tank at any time as long as the Steam Mop is unplugged. Follow the water tank filling instructions on page 11.
NOTE: Please wait 2 to 3 minutes for the Steam Mop to cool off before switching the mop head. NEVER leave the Steam Mop with a damp/wet Dirt Grip pad on any floor for an extended period of time.
Intelligent Steam Control®
The Shark® Genius™ Steam Pocket® Mop System has 3 unique Intelligent Steam Control settings so you can use the right amount of steam for the cleaning task at hand. See below for tips on when to use each setting.
TO SANITIZE* WITH THE STEAM MOP USING THE GENIUS™ MOP HEAD AND THE DIRT GRIP™ PAD:
- Attach a clean Dirt Grip pad to the Genius Mop Head.
- Plug in the unit and press the Steam Control Button to select the HI Setting.
- Wait 30 seconds for the unit to begin producing steam.
- Start mopping on an appropriate sealed hard floor surface with a forward and backward motion. After three minutes, your unit is ready to be used to sanitize.
- Using a forward and backward motion, move the unit slowly and evenly over the area to be sanitized while applying continuous downward pressure. Slowly repeat at least 3 times. * Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary. With Genius Mop Head in HI mode only when used with Steam Mop. Not in Steam Blaster mode.
Caring for Your Steam Pocket® Mop
AFTER USE AND STORAGE
- Press the Steam Control Button until the three lights below start to blink, indicating that you are in Standby mode. Unplug the cord from the outlet and place the Steam Mop into the upright position. Let it cool.
- To remove the Dirt Grip™ pad, lift the Steam Mop straight up by the handle until the Genius™ Mop Head is hanging straight down. Press the Release button on the back of the mop body, and both sides of the mop head will drop open, releasing the pad. Once the pad has been released, close the mop head.
- If the Genius Mop Head is not attached to the mop, the pad can still be removed. Press the two red Secondary Release Buttons located on the sides of the mop head post to release the pad (fig. 12).
- Empty the water tank before storing. To empty the tank, hold the Steam Mop beside a sink. Open the water tank lid, then lean the unit over the sink. Let the water drain out, then close the lid.
- To store the Steam Mop, wait until after it has cooled and the steam has been released. Then remove the Genius Mop Head and hang the mop by its handle on a large hook (not included) (fig. 13).
DIRT GRIP PAD CARE INSTRUCTIONS
Care
Machine-wash the Dirt Grip pads separately with warm water using liquid detergent.
NEVER USE BLEACH, POWDERED DETERGENT, OR FABRIC SOFTENERS as they may damage or leave a coating on the Dirt Grip pads that will reduce their cleaning performance and absorbency. Dirt Grip pads should be line-dried or tumble-dried on a low setting, as this will extend the life of the microfiber fabric (fig. 14). Loose fibers can indicate wearing of the microfiber fabric. DO NOT pull the loose fibers, as this can cause the weave to come undone. Simply trim the loose fibers with scissors (fig. 15).
Replacement Dirt Grip pads
For best cleaning results, we recommend replacing your Dirt Grip pads every 3 to 4 months following normal use. As with any fabric, dirt particles, grease, friction, and repeated washing can cause the fibers to break down, and you may notice an increase in the effort needed to push or pull the mop. You can purchase replacement Dirt Grip pads and other accessories by visiting sharkclean.com or calling 1-800-798-7398.
STEAM NOZZLE CARE
If you believe the main steam nozzle or the Steam Blaster™ nozzle is clogged, please contact Customer Service at 1-800-798-7398 or sharkclean.com
Ordering Additional Accessories
Troubleshooting Guide
Frequently Asked Questions
DOWNLOAD LINK
Shark S5003D Genius Steam Pocket Mop System Owner Guide
https://www.sharkclean.com/
