Yamaha YME22700 Jet Pod Pro User Manual
INTRODUCTION
The single thruster Yamaha JET POD PRO is a full-featured Seascooter that gets you cruising underwater with a top speed up to 5.3 mph (8.5 km/h). Easily shift between 3 rotational speeds as you conserve your energy for more bottom time. Use appropriate equipment such as wet suit, approved life jacket, mask & snorkel etc. when using Seascooter. Only operate the Seascooter in water.
- Extreme compact and hydrodynamic design
- Foldable control handles for compact storage and travel size
- Heavy-duty retractable rubber carry handle for easy transport
- Quick set up design for instant use
- Single motor design for better maneuverability
- Run up to 65 minutes (Normal Use)
- Weigh just 8.36 lb / 3.8 kg including battery
- Rated to 100 ft / 30m
- Speed up to 5.3 MPH / 8.5 KM/H
PARTS DIAGRAM
- Front Grille
- Camera Mount (Camera not included)
- Speedo Control
- Start Buttons
- Control Handles (Foldable)
- Battery Indicator
- Foldable Control Handles Release Buttons
- Carry Handle
- Battery
- Battery Charging Base
- Charger
BATTERY INSTRUCTION
CHARGING INSTRUCTION:
- Always ensure the control handles are folded away before removing the battery (see Fig. 1)
- ALWAYS ensure that the Seascooter is out of the water, dry and placed in a dry area.
- Pull the two latches down and remove the battery (see Fig. 2)
- Make sure the battery terminals are dry and clean.
- Connect the charging base to the charger body. (see Fig. 3)
- Place the battery onto the charging base. (see Fig. 4)
- Charging will take around 3 hours. When the Battery Pod is charging, the LED light of the charger turns RED. When the battery is fully charged, the LED light turns GREEN (see Fig. 5)
- Once the battery is fully charged, remove it from the charging base. (see Fig. 5)
REPLACING THE BATTERY:
- Make sure the battery terminals are dry and clean. (see Fig. 6)
- Make sure the o-rings on the battery terminals are in place. The o-ring must be clean. (see Fig. 7)
- Align the terminals on the sea scooter with the terminals on the battery. (see Fig. 8)
- Make sure the 2 latches are spread out wide. Slide the battery into the seascooter body according to the Fig. 9
- Press the battery into the seascooter. Close the latches to lock the battery. (see Fig. 10)
GETTING STARTED
To use the Seascooter, follow these instructions.
- Follow instructions on page 6 and charge the battery just before use.
- Place the Seascooter into the water and rock gently to release trapped air.
- The seascooter unit automatically assumes neutral to positive buoyancy in seawater. It will have less buoyancy in fresh water and pool and may sink in such waters.
- Slide the Foldable Control Handles Release Buttons, to fold out the control handles. (see Fig. 11)
- Make sure the seascooter is in correct position for use. (see Fig. 12)
- When ready to set off, pull both triggers to start the seascooter (see Fig. 13).
- Simply push the speed control button to adjust the speed. (see Fig. 14)
- To stop the Propeller, simply release both triggers.
- Keep checking the LED light on the battery indicator when using the seascooter. (see Fig. 15) (Indicator diagram) The battery is full when all the LED lights are on. (Indicator diagram) The battery capacity drops to 40% when battery indicator shows 2 red lights, (Indicator diagram) The battery capacity drops to 20% when battery indicator shows 1 red light, Make sure sufficient charge remains in the battery for returning to the start point.
- Always ensure the control handles are folded away when the seascooter is out of water. (see Fig. 16)
- Maintain proper posture to achieve the maximum speed when using the Seascooter. (see Fig. 17)
BUILT-IN CARRY HANDLE
- The Jet Pod foldable control handles can be folded away to achieve a highly compact storage and travelling size. When not in use and with its control handles folded away the unit features a retractable rubber carry handle that can be easily pulled and pressed back into seascooter body to allow for easy
transport and handling. - When carrying the Jet Pod, pull out the carry handles from the seascooter body (see Fig. 18)
- Press the carry handle back into the seascooter body when use. (see Fig. 19)
Folding away the control handles
- Press the buttons underneath the control handles (see Fig. 20)
- Fold away the control handles until you hear a click sound and the control handles are locked. (see Fig. 21)
Note:
- If there is no operation for a long time, the product will be turned off automatically. Fold away the control handles when not in use.
- Please do not replace the battery in water.
CARE & MAINTENANCE
Washing and Care
- Method A: Soak the Seascooter in fresh water for approx. 1 hour after every use to prevent salt-sand and chlorine crystal accumulation in the Seascooter
- Method B: Switch the Seascooter on for approx. 1 minute in fresh water to flush the Seascooter and propeller components clear of any debris Visit our YouTube channels “Yamaha Seascooters” for video instruction.
To clean the Seascooter do not use detergents; only use a damp cloth to wipe the unit clean.
- Use a cloth to dry the Seascooter and the battery compartment.
- DO NOT leave the Seascooter in the water. Always take the unit out of water when not in use.
Sand or Grit on Seals
Ensure that sand/grit does not get on the seals as correct maintenance and care is essential. To remove sand or grit from the seals, rinse the seals in fresh water and apply fresh lubricant. If there is sand inside the Battery Housing, gently brush the sand from the unit taking care not to scratch the sealing surfaces.
TECHNICAL SPECIFICATIONS
- WEIGHT 8.36 LB / 3.8 KG 16+
- DEPTH 100 FT / 30 M
- RUN TIME 65 MINUTES (NORMAL USE)
- SPEED UP TO 5.3 MPH / 8.5 KM/H
- GEAR 3 SPEEDS
- RECHARGE 3 HOURS
- BATTERY 14.4V / 10 AH
- HAND-CARRY IN YOUR FLIGHT
Unit Dimensions
- 8.7 inches x 11.6 inches 221 x 295 mm