GE 34459 6 Device Universal Remote User Manual

GE 34459 6 Device Universal Remote User Manual

Setup

Your universal remote requires two (2) AAA batteries (not included). Alkaline batteries are recommended.

Battery Installation

• On the back of the remote, slide the cover down to remove.
• Match the (+) and (-) marks on the batteries to the (+) and (-) marks inside the battery compartment, then insert two (2) AAA batteries. Be sure to use fresh batteries.
• Slide the battery cover back into place.

NOTE: If your remote stops operating properly,replace the batteries with new ones. The remote will retain the codes you have programmed for up to 10 minutes after the batteries are removed.

Battery Precautions

• Do not mix old and new batteries.
• recharged Nitre baterin, or
• Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with local and national regulations.

Battery Saver

Your remote automatically turns off if the buttons are depressed more than 8 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed le.g., between the sofa cushions).

Code Saver

You will have up to 10 minutes to change the batteries in your remote without losing codes you have programmed. However, do not press any buttons until batteries are installed in the remote. If buttons are pressed without batteries in the remote, all codes will be lost.

Button Functions

• Red Indicator lights when any button is pressed.
• TV, DVR, CBL, B-RAY, AMP, AUX Selects device to control.
• UP, DOWN, LEFT & RIGHT Navigation buttons. INPUT Selects the video inputs from available viewing sources.
• GUIDE Displays satellite or cable on-screen. DVR LIST Displays list of recorded programs
• VOLUME UP/DOWN Changes the volume level of the device, normally the TV.
• CHANNEL UP/DOWN Changes the channed ay LAST Returns to the previously selected channel.
• EXIT Exits On-Screen Menus and/or| Retums to previous On-Screen selection. RECORD, PLAY, STOP, REW, FF, PAUSE
• DOT: Used to select digital channels, e.g., 2.3.

• OK Selects menu items for the device you are controlling.
• SETUP Button is used to program the remote SHIFT is the alternate function of this button.
• Use the SHIFT button to access the menu and DVR list of your device. To enter the SHIFT mode press this button once. To exit the shift mode, press the SHIFT button again.
• INFO Displays/selects on-screen channel information.
• MENU Displays the Menu on the TV. nS.10 MUTE Turns off the TV sound while the picture remains.
• Fav Allows user to program up to 10 of their favorite channels for quick A, B, C, D Colored ABCD buttons for menu navigation in DVRs and set top boxes
• NUMBERS Enter numbers for direct channel selection. Some devices require ENTER to be pressed after channel selection.

Programming Your Remote

Your GE universal remote control is designed to control multiple audio/video devices such as a TV, DVD, DVR, satellite, cable and audio device using only one remote. To use this remote, you will need to program it to control the devices of your choice. There are two ways to program the remote – direct code  entry or auto code search.

Direct Code Entry (Recommended)

• Locate the Remote Code List provided in this manual. Find the DEVICE CATEGORY you wish to program (for| example TV, DVR, CBL, B-RAY, AMP,AUX) and then find the BRAND of that device. Circle all the codes under that  brand. Example: For a GE TV, locate the TV code section then circle all of the GE TV codes.
• Manually turn on the device you wish tocorans.io
• Press and hold the SETUP button until the red indicator light stays on (approximately 2 seconds) and then release the SETUP button.
• Press and release the device button on the remote (TV, DVR, CBL, B-RAY, AMP, AUX). The red indicator will blink once and then remain on.
• Enter the first 4-digit code previously found in the code list using the number buttons on the remote. If the code entered is a valid code, the red indicator light will turn off. If the code entered is not a valid code, the red indicator light will flash and remain on allowing you to re-enter the code.

Note: If no buttons are pressed for 35 seconds, the remote will exit the SETUP mode and you will have to start over.

• Point the remote at the device. Press the POWER button-if the device turns off, no further programming is required for that device. If the device does not turn off, return to steps 3-5 and use the next code found in the code list. Continue this process until a code for your device is found.
• Repeat this process for each device (for example TV, DVR, CBL, DVD, AMP. AUX) in your home entertainment system you wish to control.

Programming Notes

• If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote.
• Sometimes the first epfe that works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.
• With the Direct Code Entry method, you can program any device button to control any device in your home entertainment system. For example, you can use the DVR device button to control an audio receiver or a DVD, VCR, satellite device, etc.
• For combination devices, you may have to enter a code for each device. For example, for a VCR/DVD device, you may have to enter a code for the DVD under the DVD button and enter a code for the VCR using a different device button on the remote.
• Write down the code found to operate your device for future reference.

Auto Code Search

The Auto Code Search, searches automatically through all of the codes stored in this remote. Read all the following steps prior to starting the auto code search as you will need to be prepared to lock-in the proper code when found.

• Manually turn on the device you wish to control.
• Press and hold the SETUP button until the red indicator light stays on (approximately 2 seconds and then release the button.
• Press and release the device button on the remote (TV, DVR, CBL, B-RAY, AMP, AUX) for device you wish to control. The red indicator will blink once and then remain on.
• Point the remote at the device and press and release the POWER button (for T/bE PLAY button (for DVD, VCR, etc.) to start the search. The red indicator will flash (approximately every 2 seconds) as the remote searches. Note: The remote must be pointed at the device for the duration of this search.
• Place your finger on the #1 button so you are prepared to lock-in the code.
• When the device shuts off or begins playing, press the #1 button to lock-in the code. The red indicator light will turn off. Note: You have approximately two seconds after the device shuts off or begins playing to lock-in the code.
• Point the remote at the device and check to see if the remote operates the device as desired. If it does, no further programming is required for that device. If it does not, return to step 2 and start the auto code search again.
• Repeat this process for each device (for example TV, DVD, SAT, AUX) in your home entertainment system you wish to control.

Programming Notes

• This process may take several minutes as the remote contains many codes.
• When using the Auto Code Search programming method, the device button corresponding to the type of device you want to control must be selected (for example, the TV device button must be selected in step 3 if you want to control a TV. the DVD device button for a DVD player, etc.)
• The SETUP button can be used during the search process to reverse the direction of the search of the remote codes. For example, if you miss the code for your device and the remote is continuing poste seriorited by a binode selina reverse direction and return to the code.
• Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Continue the auto code search as directed above until the best code is found.

Controlling Combo Devices

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/ VCR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device. For example, if you have a TV/DVD Combo, you might need to set up one code under the TV button to control the TV part AND a separate code (under any other Mode button) to control the DVD part.

Favorite Function

Allows user to program up to 10 of their favorite channels for quick access. Setup Favorite Function

• Press and release the device button (TV, DVR, CBL, B-RAY, AMP, AUX). The indicator light will blink once. Special

Note: User must select the device type that controls the channels; for example if a user has a Cable Box for controlling channels, then this device button must be selected to properly change the channels on the cable box.

• Press and hold the SETUP button for 2 seconds or until the red indicator light turns on, then release the SETUP button.
• Press and release the FAV button. The red indicator will blink once
• Presentereos the numerical button 0 – 9) that you will use for storing your favorite channel. The red indicator will blink once and remain on.
• Enter the channel number you wish to program, for example channel 4, 21, 4-1, 52-2.
• Press and release the FAV button, the red indicator will turn off. Your favorite channel is now saved.
• Process can be repeated for up to 10 of your favorite channels.

Using Favorite Function

• Press and release the FAV button. The red indicator light will turn on.
• Press and release the programmed button (0-9). The red indicator will blink twice and the remote will send the code for your pre-programmed channel.

Master Volume Feature

The Master Volume Feature allows you to select a single device (TV or audio receiver) that the volume control always controls. For example, the remote can be in TV mode while the volume buttons control the volume on your audio receiver instead of your TV. Enabling the Master Volume Feature

• Press and hold the SETUP button until the red indicator stays on (approximately 2 seconds) and then release the button.
• Press and release desired device button (TV, DVR, CBL, B-RAY, AMP. AUX) for the device you wish to setup to always control the volume.
• Press and release the MUTE button.
• Press and release the VOL + button. The red indicator will blink twice and then/gbaftS.IO

To test the feature put the remote in another mode such as the TV mode if you programmed the audio receiver to be the Master Volume Device. Point the remote at the audio receiver, press and hold either the VOL – or the VOL + button. If the audio receiver volume changes then the remote is programmed correctly. If the TV volume changes and not the audio receiver, you will have to repeat the steps above and test again.

Disabling the Master Volume Feature

• Press and hold the SETUP button until the red indicator stays on (approximately 2 seconds) and then release the button.
• Press and release the device button (TV, DVR, CBL, B-RAY, AMP, AUX) which is programmed to control the Master Volume Feature.
• Press and release the MUTE button
• Press and release the VOL – button. The red indicator light will blink twice and go off.

Code Identification

• Press and hold the SETUP button until the red indicator stays on (approximately 2 seconds) and then release the button.
• Press and release the desired device button (TV, DVR, CBL, B-RAY, AMP. AUXI you would like the code for.
• Press and release ENTER button.
• Press and release the #1 button. Count the number of times the remote light flashes. This is the number corresponding to the first digitif thelogde Repeat the process by pressing the #2, #3 and #4 buttons for the remaining digits.
• Press and release ENTER button to exit this mode.

Reset to Factory Settings

• Press and hold the SETUP button until the red indicator stays on (approximately 2 seconds) and then release the button.
• Press and release the MUTE button.
• Press and release the number #0 button. The red indicator light will flash twice.

Using Your Remote

Using SHIFT for Menu and Navigation The SHIFT button allows access to more than one function for certain buttons.

Note: the red indicator light will blink in shift mode.

Use the SHIFT/SETUP button prior to accessing the DVR LIST, MENU, EXIT for example:

• For Menu, press and release SHIFT/SETUP Do then INFO/MENU.
• The LAST EXTe release SHIFT/SETUP SPECIAL NOTE: Remote will stay in shift mode until the SHIFT button is pressed agqin, or until 10 seconds of inactivity.

Troubleshooting

• Remote does not operate your device.
• Press the device button of the device you wish to control.
• Program the remote with a new code.
• Install new batteries. (You might have to reprogram your remote after installing new batteries.)
• Remote may not be compatible with your device. Remote does not operate some features of your device.
• Sometimes a particular code might operate some features but not all. Try programing remote with a new code.
• Remote may not be able to operate all features of your device or button names might be different than that of your original remote. Red Indicator blinks and staysion after you program a product code.
• Remote did not accept the code.
• Try to program the code again or try a different code.
• Remote Code is not available for a combo device (e.g. TV/VCR)
• See section for controlling combo devices. aditional innuest pese visit lur web site www.jascoproducts.com, or contact our Technical Support Group at 1-800-654-8483.

REFRENCE LINK

https://www.ge.com/